Book Now

 

 

How do you actually feel in relation to How to Install a Bathtub Yourself?

Mounting a bathtub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily accessible, the project can move rapidly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a brand-new bath tub in your washroom if you have actually currently gotten a brand-new tub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices and also product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Setting up the Tub

Making use of both wooden boards under its feet, put the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the bathtub up until the level reviews level.
To install faucets, fit all-time low of the outermost flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait up until the tub has been utilized a minimum of when as this will certainly resolve it right into its last setting.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can crack rather early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading up on Tools You Need to Install a New Bathtub ? Post a remark further down. We would be interested to hear your ideas about this write-up. Hoping to see you back again in the near future. Enjoyed our piece of writing? Please share it. Let someone else discover it. Thank you so much for going through it.

Schedule Appointment